Runco CL-420 Especificaciones Pagina 54
- Pagina / 72
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operation
44 Runco CL-410 and CL-420 Owner’s Operating Manual
ISF Settings Use the ISF Settings menu to perform advanced picture quality adjustments. This menu
should be used by ISF-certified technicians only.
Several controls in this menu are identical to those in the Picture Adjust menu, but are
accessible only by entering the ISF Calibration menu passcode. This makes it possible to
restore the picture quality settings to what they were when the projector was installed,
simply by recalling the “ISF Night” or “ISF Day” preset.
Brightness: Refer to Brightness on page 35.
Contrast: Refer to Contrast on page 36.
Color: Refer to Color Saturation on page 36.
Tint: Refer to Tint on page 37.
Sharpness: Refer to Sharpness on page 38.
Gamma: Refer to Gamma on page 38.
Color Temp: Refer to Color Temperature on page 39.
Picture Setting: To recall the Custom1, ISF Night or ISF Day settings, choose Picture
Setting from the ISF Calibration menu. Then, select “Custom1,” “ISF Night” or “ISF Day”
and press ENTER, or use the corresponding buttons on the remote control.
White Balance: Refer to White Balance on page 40.
Save Settings: For each input and supported resolution, the CL-410/CL-420 lets you
save image quality settings as presets that you can recall at a later time. You can create
up to three presets -- designated “Custom1,” “ISF Day” and “ISF Night” -- per input and
resolution.
You should save changes to any of the following settings to a preset; otherwise they will
be lost when a new input source or resolution is selected:
• Aspect ratio
• Picture adjustments (brightness, contrast, color saturation, tint, sharpness, gamma,
color temperature, ICC selection and white balance settings)
• Image options (SDTV adjust settings, brightness enhance, lamp power)
To save image settings in the “ISF Day” or “ISF Night” preset, select Save Settings from
the ISF Calibration menu and select “ISF Day” or “ISF Night.” (To save settings to the
“Custom1” memory preset, refer to
Save Settings on page 40.)
Lamp Timer Reset: When you replace the projector lamp, you should also reset the
lamp hour counter. To do this, select Lamp Timer Reset from the ISF Calibration menu
and press ENTER. The CL-410/CL-420 shows the number of hours the projector lamp
has been in service and asks you to confirm or cancel the reset. Press ENTER to confirm
or EXIT to cancel.
For detailed lamp replacement instructions, refer to Lamp Replacement on page 50.
ISF Calibration
Brightness 0
Contrast 0
Color 0
Tint 0
Sharpness 3
Gamma 2.2
Color Temp 6500K
Picture Setting
White Balance
Save Settings
Lamp Timer Reset
ICC Adjust Standard
ISF Enable OFF
Blue Enable OFF
Splash Screen Timer 60 secs
Noise Reduction 0
➤
You must enter a passcode to access the ISF Settings menu.
Note
- OWNER’S OPERATING MANUAL 1
- TWO YEAR LIMITED WARRANTY 3
- Safety Precautions 6
- Table of Contents 7
- List of Figures 10
- 1. Introduction 11
- Using This Manual 12
- Description, Features 13
- Introduction 14
- 2. Controls and Functions 15
- Controls and Functions 16
- Remote Control 18
- CL-410/CL-420 18
- 3. Installation 21
- Installation 22
- Quick Setup 23
- Considerations 24
- Ceiling Installation 26
- Floor Installation 26
- Connections to the 30
- Personal 32
- Computer 32
- Component 33
- Video Source 33
- (DVD Player 33
- DVD Player, VCR 34
- Satellite Receiver 34
- To PC or Automation/ 35
- Control System 35
- 4. Operation 37
- Operation 38
- Zoom inZoom out 39
- Lens shift dial 40
- (Horizontal) 40
- (Vertical) 40
- Save Settings 41
- Active Image 43
- Area (4:3) 43
- 2.35:1 Image on 44
- 16:9 Screen with 44
- Virtual Cinema 44
- Below Black 45
- Color Temp 6500K 49
- Reset Color Temp 49
- CALIBRATED FOR: 55
- CUSTOM BUILT BY: 55
- Cleaning the Projector 57
- Cleaning the Lens 57
- Side and front view 58
- Ventilation holes 58
- Power OFF 58
- Lamp Cautions 59
- Lamp Replacement 60
- Troubleshooting Tips 61
- 6. Serial Communications 63
- 7. Specifications 65
- Dimensions 67
- Computer Signal 68
- Compatibility 68
- Video Signal 70
- RUMA-011170 72
Relacionado con productos y manuales para Proyectores de datos Runco CL-420
Proyectores de datos Runco RS-440LT Especificaciones
(41 paginas)
(41 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(104 paginas)
(104 paginas)
Proyectores de datos Runco VX-2c Guia de preparacion
(36 paginas)
(36 paginas)
Proyectores de datos Runco CL-500 Manual de usuario
(32 paginas)
(32 paginas)
Proyectores de datos Runco XP-103DHD Especificaciones
(126 paginas)
(126 paginas)
Proyectores de datos Runco VX-4000d Especificaciones
(108 paginas)
(108 paginas)
Proyectores de datos Runco VX-2i Especificaciones
(112 paginas)
(112 paginas)
KIA Sorento (2011) podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Samochody KIA Sorento (2011).
Dostarczamy 1 pdf podręczników KIA Sorento (2011) do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comentarios a estos manuales