Runco REFLECTION Especificaciones Pagina 86
- Pagina / 92
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Specifications
74 Runco RS-1100 Series Owner’s Operating Manual
P
RELI
M
INARY
Brightness and Contrast: Cinema Standards Measurement System (CSMS)
Specifications
- Brightness*: 14.5 to 21.6 foot-Lamberts (fL)
- Contrast Ratio*: 200:1 to 220:1
*Variable depending on RVR setting
These measurements are taken from the projector in a controlled,
home theater environment. All measurements are made to
ANSI/NAPM IT7.228-1997 specifications using the Photo Research
PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,
Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The
projector is calibrated to a color temperature of 6,500K and has a
minimum of 150 hours of usage.
The foot-Lambert (fL) is the unit of measurement used in commercial
movie theaters to express image brightness at the screen surface. The
Society of Motion Picture and Television Engineers (SMPTE) specifies
16 fL as the target image brightness for film-based projectors using an
open gate (without film in the projector). More importantly, today
SMPTE specifies 12 fL as the target image brightness in Digital
Cinema theaters. The foot-Lambert measurement is dependent on
screen size, screen gain and projector light output.
Home Theater Calibration Specifications
- Light Output: 442 to 587 ANSI Lumens
- Contrast Ratio*: 200:1 to 220:1
These specifications are obtained by calibrating the projector as
described above for CSMS measurements.
Industry-Standard Specifications
- Light Output: 1250 ANSI Lumens
- Contrast Ratio: 1500:1 to 3100:1
These are typical projector brightness and contrast specifications
found in most companies’ sales literature. Runco includes these
measurements in its literature to allow for direct comparison with other
manufacturers’ projectors. These measurements are typically taken at
9,000K to 13,000K to get expected performance data when the
projector is used in professional, commercial and industrial displays.
Lamp: 250 Watts
Estimated Lamp Life: 2000 hours
Video Inputs: (1) Composite Video, (1) S-Video, (1) RGB/Component Video
(BNC connectors), (1) RCA Component Video, (1) HDMI
Control Options: - Discrete IR remote
- Serial commands via RS-232
RS-232 Communication
Parameters:
9600, 38400 or 115200 bps, no parity, 8 data bits, 1 stop bit,
no flow control
+12V Output: Max. 0.25 Amps, active when Cinema or Virtual Cinema
Aspect Ratio is selected (CineWide versions only) or when
projector is turned on; Tip = +12V; Sleeve = Ground
Power Requirements: 100 to 240 VAC (auto-sensing), 50/60 Hz, 310 Watts
Operating Environment: 41°F to 95°F (5°C to 35°C), 20% to 80% humidity
(non-condensing)
Dimensions: RS-1100: See Figure 7-1
RS-1100 Ultra: See Figure 7-2
Table 7-1. RS-1100 Specifications (continued)
Downloaded From projector-manual.com Runco Manuals
- RS-1100 Series 1
- TWO YEAR LIMITED WARRANTY 3
- Safety Precautions 6
- Table of Contents 10
- List of Figures 11
- Introduction 13
- Using This Manual 14
- Related Documents 14
- Description, Features 15
- 2. Controls and Functions 17
- Controls and Functions 18
- RS-1100 Rear Panel 19
- RS-1100 Remote 21
- Installation 25
- Quick Setup 26
- Considerations 27
- Ceiling Installation 30
- Floor Installation 30
- Installing the Optional 33
- CineWide/AutoScope 33
- Lens Motor (RS-1100 33
- Ultra only) 33
- Ceiling Mount 35
- Extension Brackets 35
- Mounting the RS-1100 36
- Connections to the 37
- DTV Source 40
- DVD Player, VCR 40
- Satellite Receiver 40
- D-Sub 9-pin female 41
- RJ-11 Male 41
- RJ-11 to 41
- D-Sub 9-pin Adapter 41
- (not included) 41
- Turning on the Power 43
- Installing and 45
- Adjusting the 45
- CineWide Anamorphic 45
- Too Far Right 47
- Too Far Left 47
- Correct position 47
- Too High 48
- Correct Lens Angle 48
- Incorrect Lens Angle 48
- Anamorphic Lens (Top View) 49
- 7 Pitch Adjustment 52
- Yoke for Lens 52
- 8 Lens 52
- Adapter Ring 52
- 9 Anamorphic Lens 52
- Operation 55
- Store Custom 1 57
- (see above) 57
- Below Black 59
- Active Image 64
- Area (4:3) 64
- 2.35:1 Image on 65
- 16:9 Screen 65
- )V( EGNAR TUPNI 69
- Remote Control 73
- Secondary 20 73
- Lamp Replacement 77
- Troubleshooting Tips 78
- Serial Communications 81
- Specifications 85
- RS-1100 Dimensions 88
- RS-1100 Ultra 89
- Dimensions 89
- RUMA-011215 92
- SERIAL NUMBER 92
Relacionado con productos y manuales para Proyectores de datos Runco REFLECTION
Proyectores de datos Runco D-73d Ultra Especificaciones
(152 paginas)
(152 paginas)
Proyectores de datos Runco CL-410 Especificaciones
(57 paginas)
(57 paginas)
Proyectores de datos Runco VX-1000d Especificaciones
(90 paginas)
(90 paginas)
Proyectores de datos Runco CL-610LT Especificaciones
(56 paginas)
(56 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(88 paginas)
(88 paginas)
Proyectores de datos Runco VX-60d Especificaciones
(126 paginas)
(126 paginas)
Proyectores de datos Runco DR-300c Manual de usuario
(36 paginas)
(36 paginas)
Proyectores de datos Runco CL-420 Especificaciones
(72 paginas)
(72 paginas)
Kenwood KDC-3026R manuals
Owner’s manuals and user’s guides for Car media receivers Kenwood KDC-3026R.
We providing 1 pdf manuals Kenwood KDC-3026R for download free by document types: User Manual
Comentarios a estos manuales