Runco VX-60d Especificaciones Pagina 58
- Pagina / 126
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation
42 Signature Cinema™ SC-50d/SC-60d Installation/Operation Manual
PRE
L
IMINAR
Y
3.9
Primary Lens
Adjustments: Focus,
Zoom and Position
Lens zoom, focus and position are motorized adjustments that are adjustable using the
remote control (Figure 2-5). This allows you to adjust the focus and image size while at the
screen for more accurate results.
To access the motorized lens controls:
1. On the DHD Controller remote control or front panel, press MENU.
2. Select Service from the Main Menu and enter the Service Menu passcode.
3. Select Display Device from the Service Menu.
4. Select Configure from the Display Device menu, then select Lens.
The Lens menu gives you a great deal of control over the picture size, position and focus:
Focus To focus the projected image, use the cursor buttons to highlight “In” or “Out.” Then,
press and hold the ENTER button.
Zoom To make the picture smaller (zoom out), use the cursor buttons to highlight the minus sign
(-). Then, press and hold the ENTER button.
To enlarge the picture (zoom in), use the cursor buttons to highlight the plus sign (+).
Then, press and hold the ENTER button.
Vertical and Horizontal
Lens Shift
To change the lens position, use the cursor buttons to highlight “Left,” “Right,” “Up” or
“Down” in the Lens menu. Then, press and hold the ENTER button to shift the lens in that
direction.
To return the lens to its home position (no horizontal or vertical shift), use the cursor
buttons to highlight “Home” in the Lens menu. Then, press the ENTER button.
3.10
Adjusting the Picture
Orientation
By default, the SC-50d/SC-60d is configured for a “floor/front” installation, in which the
projector is installed upright and in front of the screen. If it is installed behind the screen
and/or mounted on a ceiling, you must change the picture orientation. To do this:
1. On the DHD Controller remote control or front panel, press MENU.
2. Select Service from the Main Menu and enter the Service Menu passcode.
3. Select Display Device from the Service Menu.
4. Select Configure from the Display Device menu, then select Installation.
5. Select Orientation, then choose Floor/Rear, Ceiling/Front or Ceiling/Rear, to match
the installation method.
You must enter a passcode to access the Service menu.
Note
➤
➤
➤
You should copy and paste the lens position settings to all aspect
ratios and screens that will be used. Otherwise, the lens will go the
home position when the aspect ratio or screen selection changes. For
more information, refer to Copy/Paste - Aspect Ratio on page 71.
Note
You must enter a passcode to access the Service menu.
Note
- SC-50d Series 1
- SC-60d Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 8
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. Controls and Functions 21
- SC-50d/SC-60d Input 22
- Controls and Functions 23
- DHD Controller Front 24
- DHD Controller Rear 25
- Remote Control Unit 27
- 3. Installation 31
- Quick Setup 32
- Installation 33
- Considerations 33
- Estimating Throw Distance 34
- Throw Distance (TD) = 34
- Ceiling Installation 35
- Floor Installation 35
- Installing the Primary 41
- Projection Lens 41
- Installing the Optional 42
- AutoScope Lens Motor 42
- Mounting the 43
- Connections to the 45
- SC-50d/SC-60d and 45
- Figure 3-14 50
- Audio Processor/ 52
- Switcher 52
- Secondary Display 52
- Control System 53
- IR Sensor 55
- IR Repeater 55
- Remote Control 55
- Ferrite sleeveAC power cord 56
- To power outlet 56
- To Projector AC IN 56
- Turning on the Power 57
- Adjusting the Image 59
- Geometry 59
- Installing and 61
- Adjusting the 61
- CineWide Anamorphic 61
- Too Far Right 63
- Too Far Left 63
- Correct position 63
- Too High 64
- Correct Lens Angle 64
- Incorrect Lens Angle 64
- Anamorphic Lens (Top View) 65
- Working With the 66
- 4. Operation 67
- Operation 68
- 4:3 Image on 70
- 16:9 Display 70
- (Letterbox aspect ratio) 70
- 1080i HDTV Image 71
- 720p HDTV Image 71
- Below Black 73
- 7 Auto Color Enable 84
- 7 Test Pattern Enable 84
- Input Names 90
- Lamp Compartment Cover 99
- Retaining Screws 99
- Troubleshooting Tips 101
- 6. External Control 103
- Table 6-1. Serial Commands 104
- Using Discrete IR 108
- Start Bits Toggle Bit 109
- Address Bits Command Bits 109
- 11010001000001 109
- Using HDMI CEC 112
- Messages 112
- External Control 114
- 7. Specifications 115
- DHD Controller 117
- Specifications 117
- SC-50d/SC-60d 119
- Dimensions 119
- Dimensions with 120
- CineWide with 120
- AutoScope Assembly 120
- Supported Timings 121
- 020-1105-01 Rev. A 126
- July 2011 126
Relacionado con productos y manuales para Proyectores de datos Runco VX-60d
Proyectores de datos Runco DR-300c Manual de usuario
(36 paginas)
(36 paginas)
Proyectores de datos Runco CL-420 Especificaciones
(72 paginas)
(72 paginas)
Proyectores de datos Runco RS-440LT Especificaciones
(41 paginas)
(41 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(104 paginas)
(104 paginas)
Proyectores de datos Runco VX-2c Guia de preparacion
(36 paginas)
(36 paginas)
Proyectores de datos Runco CL-500 Manual de usuario
(32 paginas)
(32 paginas)
Proyectores de datos Runco XP-103DHD Especificaciones
(126 paginas)
(126 paginas)
Proyectores de datos Runco VX-4000d Especificaciones
(108 paginas)
(108 paginas)
Proyectores de datos Runco VX-2i Especificaciones
(112 paginas)
(112 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales