Runco XP-103DHD Especificaciones Pagina 85
- Pagina / 126
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operation
Runco LS-10d and LS-10HBd Installation/Operation Manual 69
PRE
L
IMINAR
Y
Input Names: You can give each DHD Controller input a descriptive name. For example,
you may want to change the default input name to the type of source component
connected to it: “VCR,” “DVD,” “Laptop” et cetera. Input names can be up to 12
characters long.
To edit an input name, select Input Names from the Service menu. Press or to select
an input and press ENTER. Use the or buttons to change a character; press
or to select a character to change. When you have finished editing the input name,
press ENTER or MENU.
To restore the default input name, press repeatedly to highlight that input name in the
“Restore” column. Then, press ENTER.
Display Device - Configure: The options in the Display Device - Configure menu allow
you to change the picture orientation, perform lens adjustments or access other,
display-device specific functions.
•Installation – Orientation: Select Installation from the Display Device - Configure
menu, then select Orientation to change the picture orientation to suit the method of
installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear). Or, for
front-projection installations, use the Auto setting to have the projector automatically
determine the orientation (floor or ceiling) using an internal sensor.
•Lens: Select Lens from the Display Device - Configure menu to access the motorized
lens controls. Refer to Primary Lens Adjustments on page 42.
•Display Info.: Select Display Info. from the Display Device - Configure menu to obtain
information about the currently-installed lamp: its serial number and number of hours in
use.
Grey Bars
Use this pattern when making
brightness, contrast or white
balance (gain/offset) adjustments.
Full White
Use this pattern when measuring
or adjusting brightness, contrast or
white balance (gain/offset).
Table 4-4. Test Patterns and Their Suggested Usage (continued)
Pattern Suggested Usage
Input Names
Restore
C o mp o s i t e 1
Composite 1
C o mp o s i t e 2
Composite 2
C o mp o s i t e 3
Composite 3
C o mp o n e n t
Component
H D 1
HD 1
H D 2
HD 2
S C A R T
SCART
H D M I 1
HDMI 1
H D M I 2
HDMI 2
H D M I 3
HDMI 3
H D M I 4
HDMI 4
- LS-10HBd 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 8
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. Controls and Functions 21
- • PROJECTION LENS 22
- Controls and Functions 23
- LS-10 Rear Panel 24
- DHD Controller Front 25
- DHD Controller Rear 26
- LS-10 Remote Control 28
- 3. Installation 33
- Quick Setup 34
- Installation 35
- Considerations 35
- Estimating Throw Distance 36
- Throw Distance (TD) = 36
- Screen width (w) 36
- Ceiling Installation 38
- Floor Installation 38
- Installing the Optional 41
- Anamorphic Lens 41
- Attachment Points 42
- Mounting the LS-10 46
- Connections to the 48
- LS-10 and DHD 48
- Controller 48
- DTV-Set-Top Box 51
- (DTV-STB) 51
- RGB Camcorder 52
- Figure 3-11 53
- Control System 54
- +12V Trigger Input 55
- Hub, Router 56
- Turning on the Power 57
- Adjusting the Image 59
- Geometry 59
- Installing and 61
- Adjusting the 61
- 4. Operation 63
- Operation 64
- 4:3 Image on 66
- 16:9 Display 66
- (Letterbox aspect ratio) 66
- 1080i HDTV Image 67
- 720p HDTV Image 67
- Below Black 69
- Above Black 69
- 7 Auto Color Enable 80
- 7 Test Pattern Enable 80
- Full White 85
- Lamp Replacement 95
- Troubleshooting Tips 96
- 6. External Control 97
- External Control 98
- Table 6-1. Serial Commands 99
- DBO R/W Yes -100 100 No 101
- DGO R/W Yes -100 100 No 101
- DRO R/W Yes -100 100 No 101
- (FCS+) or (FCS-) to 102
- IBO R/W Yes -32 32 No 103
- IGO R/W Yes -32 32 No 103
- IRO R/W Yes -32 32 No 104
- SHO R/W Yes -50 50 No 108
- (VSH+) or (VSH-) to 110
- (ZOM+) or (ZOM-) to 110
- Using Discrete IR 111
- IR Command List 112
- (Standard Mode) 112
- (Extended Mode) 114
- Code on page 75) 114
- Using HDMI CEC 115
- Messages 115
- 7. Specifications 117
- DHD Controller 119
- Specifications 119
- LS-10 Dimensions 120
- Supported Timings 121
- 020-1073-01 Rev. A 126
- September 2012 126
Relacionado con productos y manuales para Proyectores de datos Runco XP-103DHD
Proyectores de datos Runco VX-4000d Especificaciones
(108 paginas)
(108 paginas)
Proyectores de datos Runco VX-2i Especificaciones
(112 paginas)
(112 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales