Runco REFLECTION Especificaciones Pagina 71
- Pagina / 92
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operation
Runco RS-1100 Series Owner’s Operating Manual 59
PRE
L
IMINAR
Y
SDTV Adjust: Use the controls in the SDTV Adj. sub-menu to improve the display of
standard-definition signals. These controls allow you to make adjustments independently
for each SD signal type (as opposed to the per-input controls in the
Picture Adjustment
menu).
•Setup: The Brightness and Contrast settings made in the Composite, S-Video,
Component YCbCr and Deinterlacer Adjust sub-menus can be recalled by choosing
the associated Video Black Level, either here or in the
Video Black Level sub-menu
(refer to Video Black Level on page 60).
• Composite, S-Video: Select Composite, S-Video from the SDTV Adj. sub-menu to
adjust the brightness, contrast, saturation (color intensity), hue (tint) and sharpness of
Composite and S-Video signals. Refer to Picture Adjustment on page 46.
• Component YCbCr: Select Component YCbCr from the SDTV Adj. sub-menu to
adjust the brightness, contrast and saturation level for SD Component signals.
• Overscan Adjust (Read-only): Select Overscan Adjust to display the incoming signal
format and the amount of horizontal and vertical overscan. To adjust the over-scan
percentage, refer to Image Over Scan, below.
• Deinterlacer Adjust: Select Deinterlacer Adjust to adjust the contrast, brightness and
saturation level for interlaced (480i or 576i) video signals.
• Video Decoder Adjust: To optimize the display of SD Component video signals,
select Video Decoder Adjust and adjust the gain on the Y, Pb and Pr channels.
Image Over Scan: Image Over Scan pushes the outside edge of the active picture area
of the video signal out beyond the edge of the display area.
Some television programs are produced based on the assumption that older television
sets may not display the outer edges of the broadcast picture area. Over scan effectively
trims away these inactive, outer edges and enlarges the remaining portion of the image to
fill the display area.
Use the on-screen slidebar to select the desired amount of over scan.
For HDTV, DVDs and other video sources, Image Over Scan is generally not necessary or
desirable.
Image Shift: The Image Shift menu allows you to precisely center the image on the
screen. (These controls are available only with a 480i source signal.)
• Horizontal: This control moves the image right or left within the area of available pixels.
• Vertical: This option moves the image up or down within the area of available pixels.
Setup 7.5 IRE
Composite, S-Video
Component YCbCr
Overscan Adjust
Deinterlacer Adjust
Video Decoder Adjust
Format NTSC
Brightness +124
Contrast +63
Saturation +110
Hue 0
Sharpness +2
Format YUV60
Brightness +124
Contrast +63
Saturation +110
Format 525i(480i)
+ 5%
Contrast +63
Brightness +124
Saturation +110
Y Gain +135
Pb Gain +135
Pr Gain +135
Downloaded From projector-manual.com Runco Manuals
- RS-1100 Series 1
- TWO YEAR LIMITED WARRANTY 3
- Safety Precautions 6
- Table of Contents 10
- List of Figures 11
- Introduction 13
- Using This Manual 14
- Related Documents 14
- Description, Features 15
- 2. Controls and Functions 17
- Controls and Functions 18
- RS-1100 Rear Panel 19
- RS-1100 Remote 21
- Installation 25
- Quick Setup 26
- Considerations 27
- Ceiling Installation 30
- Floor Installation 30
- Installing the Optional 33
- CineWide/AutoScope 33
- Lens Motor (RS-1100 33
- Ultra only) 33
- Ceiling Mount 35
- Extension Brackets 35
- Mounting the RS-1100 36
- Connections to the 37
- DTV Source 40
- DVD Player, VCR 40
- Satellite Receiver 40
- D-Sub 9-pin female 41
- RJ-11 Male 41
- RJ-11 to 41
- D-Sub 9-pin Adapter 41
- (not included) 41
- Turning on the Power 43
- Installing and 45
- Adjusting the 45
- CineWide Anamorphic 45
- Too Far Right 47
- Too Far Left 47
- Correct position 47
- Too High 48
- Correct Lens Angle 48
- Incorrect Lens Angle 48
- Anamorphic Lens (Top View) 49
- 7 Pitch Adjustment 52
- Yoke for Lens 52
- 8 Lens 52
- Adapter Ring 52
- 9 Anamorphic Lens 52
- Operation 55
- Store Custom 1 57
- (see above) 57
- Below Black 59
- Active Image 64
- Area (4:3) 64
- 2.35:1 Image on 65
- 16:9 Screen 65
- )V( EGNAR TUPNI 69
- Remote Control 73
- Secondary 20 73
- Lamp Replacement 77
- Troubleshooting Tips 78
- Serial Communications 81
- Specifications 85
- RS-1100 Dimensions 88
- RS-1100 Ultra 89
- Dimensions 89
- RUMA-011215 92
- SERIAL NUMBER 92
Relacionado con productos y manuales para Proyectores de datos Runco REFLECTION
Proyectores de datos Runco D-73d Ultra Especificaciones
(152 paginas)
(152 paginas)
Proyectores de datos Runco CL-410 Especificaciones
(57 paginas)
(57 paginas)
Proyectores de datos Runco VX-1000d Especificaciones
(90 paginas)
(90 paginas)
Proyectores de datos Runco CL-610LT Especificaciones
(56 paginas)
(56 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(88 paginas)
(88 paginas)
Proyectores de datos Runco VX-60d Especificaciones
(126 paginas)
(126 paginas)
Proyectores de datos Runco DR-300c Manual de usuario
(36 paginas)
(36 paginas)
Proyectores de datos Runco CL-420 Especificaciones
(72 paginas)
(72 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales