Runco XtremeProjection X-450d Especificaciones Pagina 117
- Pagina / 156
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Maintenance and Troubleshooting
Runco X-400d/X-450d Installation/Operation Manual 101
PRE
L
IMINAR
Y
5.1
Lamp Replacement
The lamp should be replaced when it reaches the end of its life (typically between 2,000
and 3,000 hours depending on the Lamp Power setting), or sooner if a noticeable
degradation in brightness occurs.
Keep track of the number of hours the lamp has been in use and be aware of any changes
to brightness. These indicators will help you effectively maintain operation of the projector.
To find out how long the currently-installed lamp has been in service, select Display Info.
from the Display Device - Configure menu (available by selecting Service -> Display
Device -> Configure -> Display Info., in sequence).
For lamp or filter replacement, please contact your nearest Runco authorized
service center or Runco dealer. Do not attempt to replace the lamp yourself!
1. Turn off the projector and unplug the power cord. Allow the projector to cool
down for approximately 45 minutes prior to removing the lamp assembly for
replacement.
2. Loosen the two rear Lamp Cover screws and
remove the cover.
3. Remove the two lamp assembly mounting screws.
4. Grasp the lamp assembly handle and pull gently, removing the lamp module from the
projector housing.
5. Install the new lamp module.
6. Replace the lamp cover and re-tighten all screws.
7. Turn on the Dimension Digital Controller and projector.
8. Reset the Lamp Hour counter. To do this, select Lamp Hours Reset from the Display
Device - Configure menu. A confirmation dialog box appears. Select “Yes,” then press
ENTER to continue with the reset or “No” to cancel the operation.
5. Maintenance and Troubleshooting
REMOVE THESE SCREWS
- XtremeProjection™ Series 1
- X-400d and X-450d 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 9
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. System Overview 21
- Projector 22
- 1 2 3 4 65 7 23
- DC-300 Dimension 24
- Digital Controller 24
- System Overview 25
- Remote Control Unit 28
- X-400d/X-450d Active 32
- 3D Emitter 32
- 3. Installation 33
- Quick Setup 34
- Installation 35
- Considerations 35
- Estimating Throw Distance 36
- Throw Distance (TD) = 36
- Screen width (w) 36
- Ceiling Installation 38
- Floor Installation 38
- Installing the Optional 42
- CineWide Lens Mount 42
- Mounting the 48
- Interconnections 50
- Dimension Digital Controller 51
- Audio Processor/ 52
- Switcher 52
- Secondary Display 52
- (to ctrl. system) 53
- (from ctrl. system) 53
- AutoScope Lens Motor 54
- Notebook Computer 57
- HDMI source 58
- COMPONEN T 59
- VIDEO OUT 59
- Computer 60
- Gaming Console 61
- DVD/DTV STB 61
- Camcorder 62
- Active 3D Emitter 63
- Turning on the Power 64
- Adjusting the Image 66
- Geometry 66
- Installing and 68
- Adjusting the 68
- CineWide Anamorphic 68
- Lens threads into ring 70
- Too Far Right 71
- Too Far Left 71
- Correct position 71
- Too High 72
- Anamorphic Lens (Top View) 73
- Correct Lens Angle 75
- Incorrect Lens Angle 75
- Wrong Position 76
- Correct Position 76
- 4. Operation 77
- 4:3 Image on 81
- 16:9 Display 81
- (Letterbox aspect ratio) 81
- 1080i HDTV Image 82
- 720p HDTV Image 82
- Below Black 84
- 3D Processing 91
- Reverse Eyes 91
- 7 Auto Color Enable 96
- 7 Test Pattern Enable 96
- Operation 100
- Primary Alignment 102
- Input Names 103
- SRC 1 Key 105
- Power Button 114
- Battery Status 114
- LED (Red/Blue) 114
- Lamp Replacement 117
- Troubleshooting Tips 118
- 6. External Control 121
- External Control 122
- Table 6-1. Serial Commands 123
- DBO R/W Yes -100 100 No 125
- DGO R/W Yes -100 100 No 126
- DRO R/W Yes -100 100 No 126
- IBO R/W Yes -32 32 No 127
- IGO R/W Yes -32 32 No 128
- IRO R/W Yes -32 32 No 129
- SHO R/W Yes -50 50 No 134
- (VSH+) or (VSH-) to 137
- (ZOM+) or (ZOM-) to 137
- Using Discrete IR 138
- (Standard Mode) 139
- (Standard Mode) (continued) 140
- (Extended Mode) 142
- Controller 143
- (continued) 144
- 7. Specifications 145
- Dimension Digital 148
- Specifications 148
- Supported Timings 150
- X-400d/X-450d 154
- Dimensions 154
- 020-1203-00 Rev. A 156
- September 2012 156
Relacionado con productos y manuales para Proyectores de datos Runco XtremeProjection X-450d
Proyectores de datos Runco VX-60d Especificaciones
(126 paginas)
(126 paginas)
Proyectores de datos Runco DR-300c Manual de usuario
(36 paginas)
(36 paginas)
Proyectores de datos Runco CL-420 Especificaciones
(72 paginas)
(72 paginas)
Proyectores de datos Runco RS-440LT Especificaciones
(41 paginas)
(41 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(104 paginas)
(104 paginas)
Proyectores de datos Runco VX-2c Guia de preparacion
(36 paginas)
(36 paginas)
Proyectores de datos Runco CL-500 Manual de usuario
(32 paginas)
(32 paginas)
Proyectores de datos Runco XP-103DHD Especificaciones
(126 paginas)
(126 paginas)
Proyectores de datos Runco VX-4000d Especificaciones
(108 paginas)
(108 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.081 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales