Runco D-73d Ultra Especificaciones Pagina 109
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operation
D-73d Series Installation/Operation Manual 93
• Diagnostics: Select Diagnostics from the Display Device - Configure menu, then
select Red, Green, Blue, Yellow, Cyan or Magenta to display only that color channel
(simulating a filter of that color). This can be useful for calibration or measurement
purposes.
To restore the normal picture (all colors), select White.
• Altitude: Select Altitude from the Display Device - Configure menu to control the
operation of the projector’s cooling fan.
In most cases, the default setting (Auto) will maintain the correct operating
temperature. If the display frequently turns off due to overheating, or in certain
high-altitude operating environments, you may need to change this setting to High.
Network: The options in the Network menu allow you to configure the network
communication features.
• IP Configuration: Select IP Configuration from the Network menu to either set the
IP address, subnet mask and default gateway of the Dimension Digital Controller
manually or obtain these settings automatically, from a DHCP (Dynamic Host
Configuration Protocol) server. (Most broadband routers and gateways support
DHCP.) You can also test the network connection from this menu.
• DHCP: To enable the DHCP client in the Dimension Digital Controller, select
DHCP from the IP Configuration menu and set it to On. With this setting, the
Dimension Digital Controller’s IP address, subnet mask and default gateway are
assigned by the local DHCP server.
To manually configure these values, set DHCP to Off.
• IP Address: Select IP Address from the IP Configuration menu to manually
configure the IP Address of the Dimension Digital Controller, as follows:
1. Press or to select the first, second, third or fourth byte of the address.
2. Press or to set the value of that byte. The range is from 0 to 255 inclusive.
3. Repeat Steps 1 and 2 for all four bytes of the address.
4. Press MENU when you have finished setting the address.
• Subnet Mask: Select Subnet Mask from the IP Configuration menu to manually
configure the IP subnet mask. The procedure is similar to that for setting the IP
address.
• Default Gateway: Select Default Gateway from the IP Configuration menu to
manually configure the default IP gateway. The procedure is similar to that for
setting the IP address.
• Communication Test: Select Communication Test from the IP Configuration
menu to verify proper operation of the network communication link.
To start the test, select Start Test from the Communication Test menu. The
Dimension Digital Controller displays the message “Performing Communication
Test.” When the test completes, the Dimension Digital Controller displays either
“Failed” (along with the error that occurred) or “Succeeded.”
The IP Address, Subnet Mask and Default Gateway items in the
IP Configuration menu are disabled (grayed out) when DHCP is
enabled.
Note
- 3Dimension™ Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 9
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. System Overview 23
- Projector 24
- System Overview 25
- D-73d Remote Control 31
- 3. Installation 37
- Quick Setup 38
- Installation 39
- Considerations 39
- Estimating Throw Distance 40
- Throw Distance (TD) = 40
- Screen width (w) 40
- Ceiling Installation 42
- Floor Installation 42
- 3.0 in. (76.2 mm) 46
- Clearance 46
- Installing the 47
- Optional Anamorphic 47
- Lens Mount 47
- Mounting the D-73d 52
- Mounting the 53
- Interconnections 54
- SECONDARY 55
- Audio Processor/ 56
- Switcher 56
- Secondary Display 56
- Control System 57
- AutoScope Lens Motor 58
- Notebook Computer 61
- HDMI source 62
- COMPONEN T 63
- VIDEO OUT 63
- RGB Camcorder 64
- Gaming Console 65
- DVD/DTV STB 65
- Power-Up Sequence 67
- Alignment Procedure 67
- 16:9 1080i/60 70
- Correct Lens Angle 76
- Incorrect Lens Angle 76
- Wrong Position 77
- Correct Position 77
- Vertical Keystoning 78
- Horizontal Keystoning 78
- Pincushion Distortion 78
- 4. Operation 81
- 4:3 Image on 84
- 16:9 Screen (Display) 84
- 16:9 Display 85
- (Letterbox aspect ratio) 85
- 1080i HDTV Image 86
- 720p HDTV Image 86
- Below Black 88
- Above Black 88
- Saturation 100
- Operation 101
- Primary Alignment 105
- Polarizer 115
- L R 116
- 6. External Control 119
- External Control 120
- Table 6-1. Serial Commands 121
- DBO R/W Yes -100 100 No 123
- DGO R/W Yes -100 100 No 123
- DRO R/W Yes -100 100 No 123
- IBO R/W Yes -32 32 No 125
- IGO R/W Yes -32 32 No 126
- IRO R/W Yes -32 32 No 126
- NFO R/W Yes 0 10 No 129
- Using Discrete IR 134
- (Standard Mode) 135
- (Standard Mode) (continued) 136
- (Extended Mode) 138
- Controller 139
- (continued) 140
- 7. Specifications 141
- Dimension Digital 143
- Specifications 143
- D-73d Dimensions 145
- Supported Timings 146
- 020-1082-02 Rev. A 152
- March 2014 152
Relacionado con productos y manuales para Proyectores de datos Runco D-73d Ultra
Proyectores de datos Runco CL-410 Especificaciones
(57 paginas)
(57 paginas)
Proyectores de datos Runco VX-1000d Especificaciones
(90 paginas)
(90 paginas)
Proyectores de datos Runco CL-610LT Especificaciones
(56 paginas)
(56 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(88 paginas)
(88 paginas)
Proyectores de datos Runco VX-60d Especificaciones
(126 paginas)
(126 paginas)
Proyectores de datos Runco DR-300c Manual de usuario
(36 paginas)
(36 paginas)
Proyectores de datos Runco CL-420 Especificaciones
(72 paginas)
(72 paginas)
Proyectores de datos Runco RS-440LT Especificaciones
(41 paginas)
(41 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(104 paginas)
(104 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales