Runco D-73d Ultra Especificaciones Pagina 68
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation
52 D-73d Series Installation/Operation Manual
Dimension Digital Controller
1. Select Calibration -> Adjustment Mode
and set it to Secondary.
2. Select Service -> Test Video and choose
Secondary Alignment.
Projector (Align Secondary/Right
Image with Screen)
1. Align the image to the screen by
adjusting the Right (bottom) primary
lens zoom, focus and H/V offset.
2. Tighten the Right primary lens lock
screw.
3. D-73d/CineWide with AutoScope
only: Remove anamorphic lenses.
Set the AutoScope transport motor
AC switch to the “on” position.
Note: The default warp is 46 pixels on
the left and right sides (x) and 26 pixels
at the top and bottom (y). If more is
needed, use the “Image Alignment”
controls to increase it.
Dimension Digital Controller
1. For a ceiling-mounted (inverted) and/or
rear-projection installation, select
Service -> Display Device ->
Configure -> Installation ->
Picture Orientation and set it as needed.
2. Select Aspect Ratio and set it to Cinema.
On a D-73d/CineWide with AutoScope,
this should position the anamorphic lens
transport in front of the primary lenses.
3. Select Calibration -> Adjustment Mode
and set it to Primary.
4. Select Service -> Test Video and choose
Primary Alignment.
Projector
1. (Re-)install anamorphic lenses.
2. Align the primary (left-eye) image
with the screen by adjusting the Left
(top) anamorphic lens to produce the
least amount of distortion.
Dimension Digital Controller
1. Select Calibration -> Adjustment Mode
and set it to Secondary.
2. Select Service -> Test Video and choose
Secondary Alignment.
Projector
1. Align the secondary (right-eye)
image to the screen by adjusting the
Right (bottom) anamorphic lens to
produce the least amount of
distortion.
Dimension Digital Controller (Align
Secondary Image with Primary Image)
1. Select Aspect Ratio and set it to 16:9.
2. Select Calibration -> Adjustment Mode
and set it to Secondary.
3. Select Calibration -> Image Alignment ->
Corner Alignment, check the Primary
Test Pattern
and Secondary Test Pattern
boxes and adjust corners.
4. Select Calibration -> Image Alignment ->
Midpoint Alignment, check the Primary
Test Pattern and Secondary Test Pattern
boxes and adjust midpoints.
Projector
No adjustment needed.
Note: The Primary lens image is
usually left un-warped. This provides
the best image quality and will be
un-scaled for 1080p sources. You can
adjust the Primary image if needed,
however, by setting the Adjustment
Mode to Primary, checking the
Primary Test Pattern and Secondary
Test Pattern boxes and adjusting the
corners and/or midpoints prior to this
step.
Table 3-6. D-73d Optical Alignment Procedure (with Anamorphic Lenses) (continued)
- 3Dimension™ Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 9
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. System Overview 23
- Projector 24
- System Overview 25
- D-73d Remote Control 31
- 3. Installation 37
- Quick Setup 38
- Installation 39
- Considerations 39
- Estimating Throw Distance 40
- Throw Distance (TD) = 40
- Screen width (w) 40
- Ceiling Installation 42
- Floor Installation 42
- 3.0 in. (76.2 mm) 46
- Clearance 46
- Installing the 47
- Optional Anamorphic 47
- Lens Mount 47
- Mounting the D-73d 52
- Mounting the 53
- Interconnections 54
- SECONDARY 55
- Audio Processor/ 56
- Switcher 56
- Secondary Display 56
- Control System 57
- AutoScope Lens Motor 58
- Notebook Computer 61
- HDMI source 62
- COMPONEN T 63
- VIDEO OUT 63
- RGB Camcorder 64
- Gaming Console 65
- DVD/DTV STB 65
- Power-Up Sequence 67
- Alignment Procedure 67
- 16:9 1080i/60 70
- Correct Lens Angle 76
- Incorrect Lens Angle 76
- Wrong Position 77
- Correct Position 77
- Vertical Keystoning 78
- Horizontal Keystoning 78
- Pincushion Distortion 78
- 4. Operation 81
- 4:3 Image on 84
- 16:9 Screen (Display) 84
- 16:9 Display 85
- (Letterbox aspect ratio) 85
- 1080i HDTV Image 86
- 720p HDTV Image 86
- Below Black 88
- Above Black 88
- Saturation 100
- Operation 101
- Primary Alignment 105
- Polarizer 115
- L R 116
- 6. External Control 119
- External Control 120
- Table 6-1. Serial Commands 121
- DBO R/W Yes -100 100 No 123
- DGO R/W Yes -100 100 No 123
- DRO R/W Yes -100 100 No 123
- IBO R/W Yes -32 32 No 125
- IGO R/W Yes -32 32 No 126
- IRO R/W Yes -32 32 No 126
- NFO R/W Yes 0 10 No 129
- Using Discrete IR 134
- (Standard Mode) 135
- (Standard Mode) (continued) 136
- (Extended Mode) 138
- Controller 139
- (continued) 140
- 7. Specifications 141
- Dimension Digital 143
- Specifications 143
- D-73d Dimensions 145
- Supported Timings 146
- 020-1082-02 Rev. A 152
- March 2014 152
Relacionado con productos y manuales para Proyectores de datos Runco D-73d Ultra
Proyectores de datos Runco CL-410 Especificaciones
(57 paginas)
(57 paginas)
Proyectores de datos Runco VX-1000d Especificaciones
(90 paginas)
(90 paginas)
Proyectores de datos Runco CL-610LT Especificaciones
(56 paginas)
(56 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(88 paginas)
(88 paginas)
Proyectores de datos Runco VX-60d Especificaciones
(126 paginas)
(126 paginas)
Proyectores de datos Runco DR-300c Manual de usuario
(36 paginas)
(36 paginas)
Proyectores de datos Runco CL-420 Especificaciones
(72 paginas)
(72 paginas)
Proyectores de datos Runco RS-440LT Especificaciones
(41 paginas)
(41 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(104 paginas)
(104 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.105 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales