Runco REFLECTION CL-510 Especificaciones Pagina 109
- Pagina / 126
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Maintenance and Troubleshooting
Runco SC-1 Owner’s Operating Manual 97
PRE
L
IMINAR
Y
The display is jittery or
unstable.
• Poor-quality or improperly
connected source.
• The horizontal or vertical
scan frequency of the
input signal may be out of
range for the projector.
• Ensure that the source is
properly connected and of
adequate quality for
detection.
• Correct at the source.
Image is too bright and/or
lacks definition in the bright
areas of the image.
• Contrast is set too high. • Lower the contrast setting.
Image appears “washed out”
and/or dark areas appear too
bright.
• Brightness is set too high. • Lower the brightness
setting.
Colors in the image are
swapped; for example, reds
appear blue or vice versa.
•The Red/Pr, Green/Y or
Blue/Pb outputs from the
source are connected to
the wrong inputs on the
DHD Controller.
• Ensure that the source
outputs are connected to
the correct DHD Controller
input.
The display freezes suddenly. • Excessive voltage noise on
the AC or ground input has
interrupted the projector’s
ability to lock on to a
signal.
• Power down the projector
and disconnect from AC.
Then, plug in again and
power up as usual.
The projector will not turn
back on after it was powered
down, or the image disap
-
pears during operation.
• The projector will not turn
on for several minutes after
power-down, to protect
the lamp.
• The lamp has failed.
• Wait until the LED at the
front of the DHD Controller
turns red.
• Replace the lamp.
AutoScope lens motor does
not work.
• The motor is not plugged
in and turned on, or the AC
outlet is not active.
• The motor is not
connected to a trigger
output on the DHD
Controller.
• Incorrect trigger
assignment.
• Ensure that the motor is
plugged in and turned on,
and that the AC outlet is
active.
• Check the trigger
connection between the
lens motor and DHD
Controller (
Figure 3-18).
• Correct the trigger
assignment (refer to
Configure Lens Motor
Trigger on page 51).
Table 5-1. Troubleshooting Chart (continued)
Symptom Possible Cause(s) Solution
- OWNER’S OPERATING MANUAL 1
- TWO YEAR LIMITED WARRANTY 3
- Safety Precautions 6
- Table of Contents 10
- List of Figures 11
- 1. Introduction 13
- Using This Manual 14
- Description, Features 15
- Introduction 16
- 2. Controls and Functions 17
- Controls and Functions 18
- SC-1 Input Panel 19
- SC-1 Control Panel 21
- DHD Controller Front 23
- DHD Controller Rear 24
- SC-1 Remote Control 26
- 3. Installation 29
- Quick Setup 30
- Installation 31
- Considerations 31
- 20% Offset 35
- Installing the 36
- Projection Lens, Lamp 36
- Lamp/Air Filter 38
- Lamp Cooling Compartment Door 38
- Min. 10” 41
- Extension 42
- Mounting the SC-1 43
- Remove these screws 44
- Pass cables through 44
- Replace these screws 44
- Personal Computer 48
- Red Green Blue Horiz Vert 48
- DVD Player, VCR 49
- Satellite Receiver 49
- Laser Disc etc 49
- 2 Transmit Data 50
- 3 Receive Data 50
- 5 Ground 50
- Rear Panel 51
- AutoScope Lens Motor (Rear) 51
- (male) (female) 53
- Turning on the Power 56
- Component SD NTSC 480i 57
- Cinema SC-1 57
- Maximizing Light 58
- Installing and 61
- Adjusting the 61
- CineWide Anamorphic 61
- Too Far Right 63
- Too Far Left 63
- Correct position 63
- Too High 64
- Correct Lens Angle 64
- Incorrect Lens Angle 64
- Wrong Position 65
- Correct Position 65
- Calibrating Projector 66
- Input 2 (DVI) 66
- Channel Setup 70
- No Resizing 72
- Working With the 78
- 4. Operation 81
- Chroma Delay 82
- 4:3 Image on 84
- 16:9 Screen (Display) 84
- Below Black 87
- Operation 88
- Vertical Keystone Correction 95
- Positive values 95
- Negative values 95
- Safety Guidelines 99
- Maintaining Proper 100
- Maintenance and 101
- Cleaning 101
- Lamp and Filter 103
- Replacement 103
- Remove anode connector 104
- Lens Replacement 107
- Troubleshooting Tips 108
- Table 5-2. SC-1 Error Codes 110
- 6. Serial Communications 113
- Table 6-1. Serial Commands 114
- 7. Specifications 119
- DHD Controller 121
- Specifications 121
- SC-1 Dimensions 122
- SERIAL NUMBER 126
Relacionado con productos y manuales para Proyectores de datos Runco REFLECTION CL-510
Proyectores de datos Runco D-73d Ultra Especificaciones
(152 paginas)
(152 paginas)
Proyectores de datos Runco CL-410 Especificaciones
(57 paginas)
(57 paginas)
Proyectores de datos Runco VX-1000d Especificaciones
(90 paginas)
(90 paginas)
Proyectores de datos Runco CL-610LT Especificaciones
(56 paginas)
(56 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(88 paginas)
(88 paginas)
Proyectores de datos Runco VX-60d Especificaciones
(126 paginas)
(126 paginas)
Proyectores de datos Runco DR-300c Manual de usuario
(36 paginas)
(36 paginas)
Proyectores de datos Runco CL-420 Especificaciones
(72 paginas)
(72 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales