Runco 3Dimension D-113d Especificaciones Pagina 103
- Pagina / 152
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operation
D-113d Projection System Installation/Operation Manual 87
PRE
L
IMINAR
Y
Press MENU to exit test pattern mode.
Input Names: You can give each input a descriptive name. For example, you may want
to change the default input name to the type of source component connected to it:
“VCR,” “DVD,” “Laptop” et cetera. Input names can be up to 12 characters long.
To edit an input name, select Input Names from the Service menu. Press or to select
an input and press ENTER. Use the or buttons to change a character; press
or to select a character to change. When you have finished editing the input name,
press ENTER or MENU.
To restore the default input name, press repeatedly to highlight that input name in the
“Restore” column. Then, press ENTER.
Primary Alignment
Secondary
Alignment
Dual Alignment
Use this pattern when aligning the
output from the projector’s
primary or secondary optical
engines (refer to Power-Up
Sequence and Optical
Alignment Procedure on
page 49). Select Dual Alignment
to have both optical engines
output this pattern.
3D
Use these patterns to confirm that
the left-eye and right eye images
are being processed correctly. To
do this, close your right eye while
viewing this test pattern through
the 3D glasses. If you see only the
left-eye portion, then the system is
correctly configured for 3D.
Normally, the Primary DHD
Controller processes the left-eye
image; the Secondary, the
right-eye image. To change this,
use the Reverse Eyes control in
the 3D Processing menu (refer to
Reverse Eyes on page 75).
Table 4-4. Test Patterns and Their Suggested Usage (continued)
Pattern Suggested Usage
Input Names
Restore
C o mp o s i t e 1
Composite 1
C o mp o s i t e 2
Composite 2
C o mp o s i t e 3
Composite 3
C o mp o n e n t
Component
H D 1
HD 1
H D 2
HD 2
S C A R T
SCART
H D M I 1
HDMI 1
H D M I 2
HDMI 2
H D M I 3
HDMI 3
H D M I 4
HDMI 4
- 3Dimension™ Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 9
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 3Dimension Processor: 21
- 2. System Overview 23
- Projector 24
- D-113d Input Panel 25
- System Overview 26
- Primary DHD 27
- Controller 27
- Secondary DHD 31
- Remote Control Unit 34
- 3. Installation 37
- Quick Setup 38
- Installation 39
- Considerations 39
- Estimating Throw Distance 40
- Throw Distance (TD) = 40
- 7RGG/RH 44
- Installing the Optional 45
- CineWide with 45
- AutoScope Lens 45
- Assembling the 46
- Projection System 46
- Mounting the D-113d 48
- Installing the Primary 48
- Projection Lenses 48
- Security 49
- Mounting the DHD 50
- Controllers and 50
- Interconnections 51
- Primary DHD Controller 53
- Secondary 53
- 3Dimension 53
- Processor 53
- Audio Processor/ 55
- Switcher 55
- Secondary Display 55
- Control System 56
- AutoScope Lens Motor 57
- IR Sensor 58
- IR Repeater 58
- Remote Control 58
- Power-Up Sequence 65
- Procedure 65
- 16:9/1 1080i/60 68
- Anamorphic Lens (Top View) 75
- Working With the 76
- 4. Operation 77
- Chroma Delay 78
- 4:3 Image on 81
- 16:9 Display 81
- (Letterbox aspect ratio) 81
- 1080i HDTV Image 82
- 720p HDTV Image 82
- Below Black 84
- 3D Processing 90
- Reverse Eyes 90
- 7 Auto Color Enable 96
- 7 Test Pattern Enable 96
- Operation 101
- Lamp Compartment Cover 113
- Retaining Screws 113
- Troubleshooting Tips 115
- 6. External Control 119
- External Control 120
- Table 6-1. Serial Commands 121
- DBO R/W Yes -100 100 No 123
- DGO R/W Yes -100 100 No 123
- DRO R/W Yes -100 100 No 123
- (FCS+) or (FCS-) = Start; 125
- (FCS=0) = Stop 125
- IBO R/W Yes -32 32 No 126
- IGO R/W Yes -32 32 No 127
- IRO R/W Yes -32 32 No 127
- (VSH+) or (VSH-) = Start; 133
- (VSH=0) = Stop 133
- (ZOM+) or (ZOM-) = Start; 133
- (ZOM=0) = Stop 133
- Using Discrete IR 134
- Start Bits Toggle Bit 135
- Address Bits Command Bits 135
- 11010001000001 135
- Using HDMI CEC 138
- Messages 138
- 7. Specifications 141
- DHD Controller 143
- Specifications 143
- 3Dimension Processor 144
- D-113d Dimensions 145
- AutoScope Assembly 146
- Supported Timings 147
- 020-1165-00 Rev. A 152
- October 2011 152
Relacionado con productos y manuales para Proyectores de datos Runco 3Dimension D-113d
Proyectores de datos Runco VX-1000d Especificaciones
(29 paginas)
(29 paginas)
Proyectores de datos Runco RS-440LT Especificaciones
(84 paginas)
(84 paginas)
Proyectores de datos Runco VX-2i Especificaciones
(60 paginas)
(60 paginas)
Proyectores de datos Runco 1080P Especificaciones
(92 paginas)
(92 paginas)
Proyectores de datos Runco D-73d Ultra Especificaciones
(152 paginas)
(152 paginas)
Proyectores de datos Runco CL-410 Especificaciones
(57 paginas)
(57 paginas)
Proyectores de datos Runco VX-1000d Especificaciones
(90 paginas)
(90 paginas)
Proyectores de datos Runco CL-610LT Especificaciones
(56 paginas)
(56 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(88 paginas)
(88 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales