Runco 3Dimension D-113d Especificaciones Pagina 74
- Pagina / 152
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation
58 D-113d Projection System Installation/Operation Manual
PRE
L
IMINAR
Y
Configure Lens Motor Trigger (CineWide with AutoScope):
CineWide with AutoScope maintains constant image height independent of the aspect
ratio, while using the full display resolution of the projector. It accomplishes this by moving
the anamorphic lens in front of the primary lens when widescreen material is being viewed.
When the viewer transitions back to 16:9 or 4:3 source material, the anamorphic lens
moves out of the light path.
To configure the lens motor trigger on the DHD Controller for proper AutoScope
operation:
1. Project a 2.35:1 aspect ratio test pattern or other image on the screen.
2. On the DHD Controller remote control or front panel, press MENU.
3. Select Calibration from the Main Menu and enter the Calibration Menu passcode.
4. Select Adjustment Mode from the Calibration Menu and set it to Both (if it isn’t
already). Then, press EXIT twice to return to the Main Menu.
5. Select Service from the Main Menu and enter the Service Menu passcode.
6. Select Triggers from the Service menu.
7. Assign the trigger outputs to which the lens motors are connected to the Cinema
and Virtual Cinema aspect ratios. This enables the lens motors to move the
anamorphic lenses into position (in front of the primary lenses) when either aspect
ratio is selected.
8. Select the Cinema or Virtual Cinema aspect ratio to move the anamorphic lenses into
position, if they aren’t already. To do this, press CINEMA or V-CINE on the DHD
Controller remote control (Figure 2-8), or press or repeatedly with no menus
visible on-screen.
9. Proceed as described in the following sections to adjust the top and bottom
anamorphic lenses.
Horizontal Position (X) Adjustment:
1. Select Service -> TestVideo and choose Primary Alignment (if adjusting the top
anamorphic lens) or Secondary Alignment (if adjusting the bottom anamorphic
lens).
2. Loosen the Yaw/X-Adjustment Levers underneath the lens.
3. Slowly move the anamorphic lens into place (from right to left or vice versa) so that
there are no shadows on either side of the screen.
4. When the horizontal position is properly set, tighten the Yaw/X-Adjustment Levers to
secure the lens in place.
You must enter a passcode to access the Service menu for the first
time after turning on the system.
Note
- 3Dimension™ Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 9
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 3Dimension Processor: 21
- 2. System Overview 23
- Projector 24
- D-113d Input Panel 25
- System Overview 26
- Primary DHD 27
- Controller 27
- Secondary DHD 31
- Remote Control Unit 34
- 3. Installation 37
- Quick Setup 38
- Installation 39
- Considerations 39
- Estimating Throw Distance 40
- Throw Distance (TD) = 40
- 7RGG/RH 44
- Installing the Optional 45
- CineWide with 45
- AutoScope Lens 45
- Assembling the 46
- Projection System 46
- Mounting the D-113d 48
- Installing the Primary 48
- Projection Lenses 48
- Security 49
- Mounting the DHD 50
- Controllers and 50
- Interconnections 51
- Primary DHD Controller 53
- Secondary 53
- 3Dimension 53
- Processor 53
- Audio Processor/ 55
- Switcher 55
- Secondary Display 55
- Control System 56
- AutoScope Lens Motor 57
- IR Sensor 58
- IR Repeater 58
- Remote Control 58
- Power-Up Sequence 65
- Procedure 65
- 16:9/1 1080i/60 68
- Anamorphic Lens (Top View) 75
- Working With the 76
- 4. Operation 77
- Chroma Delay 78
- 4:3 Image on 81
- 16:9 Display 81
- (Letterbox aspect ratio) 81
- 1080i HDTV Image 82
- 720p HDTV Image 82
- Below Black 84
- 3D Processing 90
- Reverse Eyes 90
- 7 Auto Color Enable 96
- 7 Test Pattern Enable 96
- Operation 101
- Lamp Compartment Cover 113
- Retaining Screws 113
- Troubleshooting Tips 115
- 6. External Control 119
- External Control 120
- Table 6-1. Serial Commands 121
- DBO R/W Yes -100 100 No 123
- DGO R/W Yes -100 100 No 123
- DRO R/W Yes -100 100 No 123
- (FCS+) or (FCS-) = Start; 125
- (FCS=0) = Stop 125
- IBO R/W Yes -32 32 No 126
- IGO R/W Yes -32 32 No 127
- IRO R/W Yes -32 32 No 127
- (VSH+) or (VSH-) = Start; 133
- (VSH=0) = Stop 133
- (ZOM+) or (ZOM-) = Start; 133
- (ZOM=0) = Stop 133
- Using Discrete IR 134
- Start Bits Toggle Bit 135
- Address Bits Command Bits 135
- 11010001000001 135
- Using HDMI CEC 138
- Messages 138
- 7. Specifications 141
- DHD Controller 143
- Specifications 143
- 3Dimension Processor 144
- D-113d Dimensions 145
- AutoScope Assembly 146
- Supported Timings 147
- 020-1165-00 Rev. A 152
- October 2011 152
Relacionado con productos y manuales para Proyectores de datos Runco 3Dimension D-113d
Proyectores de datos Runco VX-1000d Especificaciones
(29 paginas)
(29 paginas)
Proyectores de datos Runco RS-440LT Especificaciones
(84 paginas)
(84 paginas)
Proyectores de datos Runco VX-2i Especificaciones
(60 paginas)
(60 paginas)
Proyectores de datos Runco 1080P Especificaciones
(92 paginas)
(92 paginas)
Proyectores de datos Runco D-73d Ultra Especificaciones
(152 paginas)
(152 paginas)
Proyectores de datos Runco CL-410 Especificaciones
(57 paginas)
(57 paginas)
Proyectores de datos Runco VX-1000d Especificaciones
(90 paginas)
(90 paginas)
Proyectores de datos Runco CL-610LT Especificaciones
(56 paginas)
(56 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(88 paginas)
(88 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales