Runco 3Dimension D-113d Especificaciones Pagina 116
- Pagina / 152
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Maintenance and Troubleshooting
100 D-113d Projection System Installation/Operation Manual
PRE
L
IMINAR
Y
The display is jittery or
unstable.
• Poor-quality or improperly
connected source.
• The horizontal or vertical
scan frequency of the
input signal may be out of
range for the projector.
• Ensure that the source is
properly connected and of
adequate quality for
detection.
• Correct at the source.
Image is too bright and/or
lacks definition in the bright
areas of the image.
• Contrast is set too high. • Lower the contrast setting.
Image appears “washed out”
and/or dark areas appear too
bright.
• Brightness is set too high. • Lower the brightness
setting.
Colors in the image are
swapped; for example, reds
appear blue or vice versa.
• The Red/Pr, Green/Y or
Blue/Pb outputs from the
source are connected to
the wrong inputs on the
DHD Controller.
• Ensure that the source
outputs are connected to
the correct DHD Controller
input.
The display freezes suddenly. • Excessive voltage noise on
the AC or ground input has
interrupted the projector’s
ability to lock on to a
signal.
• Power down the projector
and disconnect from AC.
Then, plug in again and
power up as usual.
The projector will not turn
back on after it was powered
down, or the image disap-
pears during operation.
• The projector will not turn
on for two minutes after
power-down, to protect
the lamp.
• The lamp has failed.
• Wait until the
STANDBY LED at the front
of the DHD Controller
turns on (Figure 2-4).
• Replace the lamp.
AutoScope lens motor does
not work.
• The motor is not plugged
in or the AC outlet is not
active.
• The motor is not
connected to a trigger
output on the DHD
Controller.
• Incorrect trigger
assignment.
• Ensure that the motor is
plugged in and that the AC
outlet is active.
• Check the trigger
connection between the
lens motor and DHD
Controller (Figure 3-15).
• Correct the trigger
assignment (refer to
Installing and Adjusting
the CineWide
Anamorphic Lens on
page 56).
Table 5-1. Troubleshooting Chart (continued)
Symptom Possible Cause(s) Solution
- 3Dimension™ Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 9
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 3Dimension Processor: 21
- 2. System Overview 23
- Projector 24
- D-113d Input Panel 25
- System Overview 26
- Primary DHD 27
- Controller 27
- Secondary DHD 31
- Remote Control Unit 34
- 3. Installation 37
- Quick Setup 38
- Installation 39
- Considerations 39
- Estimating Throw Distance 40
- Throw Distance (TD) = 40
- 7RGG/RH 44
- Installing the Optional 45
- CineWide with 45
- AutoScope Lens 45
- Assembling the 46
- Projection System 46
- Mounting the D-113d 48
- Installing the Primary 48
- Projection Lenses 48
- Security 49
- Mounting the DHD 50
- Controllers and 50
- Interconnections 51
- Primary DHD Controller 53
- Secondary 53
- 3Dimension 53
- Processor 53
- Audio Processor/ 55
- Switcher 55
- Secondary Display 55
- Control System 56
- AutoScope Lens Motor 57
- IR Sensor 58
- IR Repeater 58
- Remote Control 58
- Power-Up Sequence 65
- Procedure 65
- 16:9/1 1080i/60 68
- Anamorphic Lens (Top View) 75
- Working With the 76
- 4. Operation 77
- Chroma Delay 78
- 4:3 Image on 81
- 16:9 Display 81
- (Letterbox aspect ratio) 81
- 1080i HDTV Image 82
- 720p HDTV Image 82
- Below Black 84
- 3D Processing 90
- Reverse Eyes 90
- 7 Auto Color Enable 96
- 7 Test Pattern Enable 96
- Operation 101
- Lamp Compartment Cover 113
- Retaining Screws 113
- Troubleshooting Tips 115
- 6. External Control 119
- External Control 120
- Table 6-1. Serial Commands 121
- DBO R/W Yes -100 100 No 123
- DGO R/W Yes -100 100 No 123
- DRO R/W Yes -100 100 No 123
- (FCS+) or (FCS-) = Start; 125
- (FCS=0) = Stop 125
- IBO R/W Yes -32 32 No 126
- IGO R/W Yes -32 32 No 127
- IRO R/W Yes -32 32 No 127
- (VSH+) or (VSH-) = Start; 133
- (VSH=0) = Stop 133
- (ZOM+) or (ZOM-) = Start; 133
- (ZOM=0) = Stop 133
- Using Discrete IR 134
- Start Bits Toggle Bit 135
- Address Bits Command Bits 135
- 11010001000001 135
- Using HDMI CEC 138
- Messages 138
- 7. Specifications 141
- DHD Controller 143
- Specifications 143
- 3Dimension Processor 144
- D-113d Dimensions 145
- AutoScope Assembly 146
- Supported Timings 147
- 020-1165-00 Rev. A 152
- October 2011 152
Relacionado con productos y manuales para Proyectores de datos Runco 3Dimension D-113d
Proyectores de datos Runco VX-1000d Especificaciones
(29 paginas)
(29 paginas)
Proyectores de datos Runco RS-440LT Especificaciones
(84 paginas)
(84 paginas)
Proyectores de datos Runco VX-2i Especificaciones
(60 paginas)
(60 paginas)
Proyectores de datos Runco 1080P Especificaciones
(92 paginas)
(92 paginas)
Proyectores de datos Runco D-73d Ultra Especificaciones
(152 paginas)
(152 paginas)
Proyectores de datos Runco CL-410 Especificaciones
(57 paginas)
(57 paginas)
Proyectores de datos Runco VX-1000d Especificaciones
(90 paginas)
(90 paginas)
Proyectores de datos Runco CL-610LT Especificaciones
(56 paginas)
(56 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(88 paginas)
(88 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales