Runco 3Dimension D-113d Especificaciones Pagina 106
- Pagina / 152
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operation
90 D-113d Projection System Installation/Operation Manual
PRE
L
IMINAR
Y
• Auto Perform Upgrade: If the “Auto Check For New Firmware” process
determines that a newer firmware version than the one currently installed is available,
you can have the DHD Controller automatically download and install it. To do this,
select Auto Perform Upgrade from the Auto Firmware Upgrade menu and set it to
On. The upgrade will occur the next time the DHD Controller is “power-cycled”
(powered off, then on again). If you prefer to do this manually, set it to Off. The DHD
Controller will ask if you want to perform the upgrade the next time it is
power-cycled.
• Check For New Firmware: To have the DHD Controller check for new firmware on
demand (and perform an upgrade if it finds a new version), select Check For New
Firmware from the Auto Firmware Upgrade menu. If the DHD Controller finds a new
firmware version, select Yes to perform the upgrade or No to return to the previous
menu.
• E-Mail Notification: Select E-Mail Notification from the Network menu to specify
when and to whom the DHD Controller sends error and service notification messages
via e-mail.
The notification messages are in the following format:
To: [E-Mail Address; see below]
From: [email protected]
Subject: [Type of notification] from Runco DHD4
Body:
This is an automated message sent from the Runco DHD4:
Notification: [One of the following:
“DHD Error” / “Display Error”
“Periodic Service Notification”
“Lamp Life Notification” / “Calibration Data”]
Detailed Description: [ If a DHD Error, one of the following:
“Fan Failure 1” / “Fan Failure 2”
“Overtemp 1” / “Overtemp 2”
“Initialization Failure”
If a Display Error, a device-specific
error message such as “Lamp Door Open”
If a Periodic Service Notification, the elapsed
time since the last notification
If a Lamp Life Notification, the number of hours
the lamp has been in service
If a Calibration Data message,
“See Attached File” ]
Serial Number: [DHD Controller serial number]
Customer Information: [From “Customer Information“ sub-menu;
see below]
Best Regards,
Runco International, LLC
1195 NW Compton Drive
Beaverton, OR 97006
1-800-237-8262
- 3Dimension™ Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 9
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 3Dimension Processor: 21
- 2. System Overview 23
- Projector 24
- D-113d Input Panel 25
- System Overview 26
- Primary DHD 27
- Controller 27
- Secondary DHD 31
- Remote Control Unit 34
- 3. Installation 37
- Quick Setup 38
- Installation 39
- Considerations 39
- Estimating Throw Distance 40
- Throw Distance (TD) = 40
- 7RGG/RH 44
- Installing the Optional 45
- CineWide with 45
- AutoScope Lens 45
- Assembling the 46
- Projection System 46
- Mounting the D-113d 48
- Installing the Primary 48
- Projection Lenses 48
- Security 49
- Mounting the DHD 50
- Controllers and 50
- Interconnections 51
- Primary DHD Controller 53
- Secondary 53
- 3Dimension 53
- Processor 53
- Audio Processor/ 55
- Switcher 55
- Secondary Display 55
- Control System 56
- AutoScope Lens Motor 57
- IR Sensor 58
- IR Repeater 58
- Remote Control 58
- Power-Up Sequence 65
- Procedure 65
- 16:9/1 1080i/60 68
- Anamorphic Lens (Top View) 75
- Working With the 76
- 4. Operation 77
- Chroma Delay 78
- 4:3 Image on 81
- 16:9 Display 81
- (Letterbox aspect ratio) 81
- 1080i HDTV Image 82
- 720p HDTV Image 82
- Below Black 84
- 3D Processing 90
- Reverse Eyes 90
- 7 Auto Color Enable 96
- 7 Test Pattern Enable 96
- Operation 101
- Lamp Compartment Cover 113
- Retaining Screws 113
- Troubleshooting Tips 115
- 6. External Control 119
- External Control 120
- Table 6-1. Serial Commands 121
- DBO R/W Yes -100 100 No 123
- DGO R/W Yes -100 100 No 123
- DRO R/W Yes -100 100 No 123
- (FCS+) or (FCS-) = Start; 125
- (FCS=0) = Stop 125
- IBO R/W Yes -32 32 No 126
- IGO R/W Yes -32 32 No 127
- IRO R/W Yes -32 32 No 127
- (VSH+) or (VSH-) = Start; 133
- (VSH=0) = Stop 133
- (ZOM+) or (ZOM-) = Start; 133
- (ZOM=0) = Stop 133
- Using Discrete IR 134
- Start Bits Toggle Bit 135
- Address Bits Command Bits 135
- 11010001000001 135
- Using HDMI CEC 138
- Messages 138
- 7. Specifications 141
- DHD Controller 143
- Specifications 143
- 3Dimension Processor 144
- D-113d Dimensions 145
- AutoScope Assembly 146
- Supported Timings 147
- 020-1165-00 Rev. A 152
- October 2011 152
Relacionado con productos y manuales para Proyectores de datos Runco 3Dimension D-113d
Proyectores de datos Runco VX-1000d Especificaciones
(29 paginas)
(29 paginas)
Proyectores de datos Runco RS-440LT Especificaciones
(84 paginas)
(84 paginas)
Proyectores de datos Runco VX-2i Especificaciones
(60 paginas)
(60 paginas)
Proyectores de datos Runco 1080P Especificaciones
(92 paginas)
(92 paginas)
Proyectores de datos Runco D-73d Ultra Especificaciones
(152 paginas)
(152 paginas)
Proyectores de datos Runco CL-410 Especificaciones
(57 paginas)
(57 paginas)
Proyectores de datos Runco VX-1000d Especificaciones
(90 paginas)
(90 paginas)
Proyectores de datos Runco CL-610LT Especificaciones
(56 paginas)
(56 paginas)
Proyectores de datos Runco VX-8d Especificaciones
(88 paginas)
(88 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.130 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales